Miscellanea and Photos

Hello everyone, I thought I would post some photos of the layout as I deconstruct the Gargraves track and start fitting the Peco Track in place,  also a few photos of the reason I am having to go with Peco Track, my furry brakeman Trigger who as I listed in my last post was occasionally stepping on my track which was putting dips on the rail and causing issues with my longer wheelbase locomotives.

 

Next Post I will tell about my new locomotive acquisition and the Issues it has when compared to the prototype  

A Setback With Gargraves Track

Hello everyone sorry for the lack of recent posts, have not had much time to work on the layout, even on my last vacation I did not really have much time for the layout have been busy with the family and domestic stuff. 

Anyway I had somewhat of a setback on the layout, my being cheap has caused me some trouble with using Gargraves track outdoors and it’s not what you think, that its corrosion.  

The problem is my German Shepherd, he sometimes steps on the track and Gargraves being hollow will slightly bend even though it’s on solid ballast.

The funny thing is I did not notice this with my little speeder or my 3450 class 4-6-4 Hudson, I noticed it when with great expectation I was going to run my 2-10-4 on the layout, it ran great on the indoor test track but when I tried to run it outdoors it only went a few feet and POP my 10 amp fuse blew,  I searched for the cause and what I found was with its much longer wheelbase the 2-10-4 s front pilot would dip down enough when the back half of the locomotive was above the area that dipped down and the front half would be at the bottom of the dip it caused a enough of a angle that it would touch the rails which of course shorted things out.

Anyhow I have decided the best course of action will be to change to a different brand of track and use the Gargraves for when I build the indoor storage part of my build. 

I have decided to go with Peco code 143 track, so far I bought 4 pieces of their flex track.

I will have 5 days off from work starting next week so hopefully this time I will be able to get some time to work on the layout and get the Peco Track down for testing. 

Until Next Time.

Looking Forward To Vacation Time

Hello all, not much to report at the moment, have not had much time to work on the layout in the last week or so. 

Did clean the leaves up around the track and checked on my bushes I planted last fall alongside of the track, all seem to have come through Winter just fine and  have new buds, just hope we don’t have a hard freeze between now and Spring.

I am taking some vacation next week starting Wednesday through the following Monday, so I hope I will be able to work some on hobby stuff and  post here on any accomplishments I might have achieved. 

What I want to do is run my 2-10-4 outdoors and see how it does with its new can motor.

I also hope to realign and ballast some of track I already have down and lay some more drainage pipe road bed.

Stay Tuned

Adapting A Lionel ZW 275 Watt AC Transformer To DC Power

Hello everyone I decided to make use of my old Lionel 275 watt ZW AC transformer and adapt it to use with my DC 2 rail trains until I can decide what DCC system and decoders to use. Other people have done this and it’s very easy to do.   Below is a film of my engine running back and forth on the Outdoor test track using the ZW plus some pictures of a wiring diagram and the buildup of the AC to DC converter using a bridge rectifier.

Disclaimer:  

Doing electrical work with these old transformers can be dangerous, proceed at your own risk.                  

I am not responsible if you burn your house down, burn your layout to ashes, melt your favorite train into a molten blob of metal or plastic goo,etc. etc.  
This post is how I did it and is for entertainment use only.

I noticed I need to do some track realignment and some ballast work, but all in all everything seems to have made it through the winter fairly well. All I did was wiped the track down with a mixture of WD-40 and 91% rubbing alcohol, set the 3451 on the track and test ran it back and forth. 

Here is the Radio Shack 25 amp full-wave Bridge Rectifier glued to the inside bottom of a plastic container.

Here is an overall view of the set up before wiring. (Please note the rocker switch on the lid was the wrong style of switch, I ended up replacing it with a DPDT toggle switch that I put on the lid in later photos, since I had already drilled the hole I just left the rocker switch in place rather than having a hole in the lid)

A hole was drilled on front and back side for the wires to go through.

Here is  wiring diagram I tried to draw up,

Black wire on the common and the red wire on A

Here is the wiring going from the transformer into the Bridge Rectifier

Here is the wiring going to the DPDT Switch (Please note you are looking at the switch from the bottom instead of from the top like the drawing

Here is another view of the wiring going to DPDT Switch.

Here is an overhead view of the box which is how the wiring diagram is depicting.

Here I am testing voltage on the layout next to the transformer I got a reading of 17.65 volts.

  

I then went to the other end of the layout and it brought up a reading of 17.63 volts, not to bad considering that it's going through just track pins, none of the feeder wires and main buss wires are hooked up yet.  I have to say I am very satisfied with the results, especially considering the track has been out in the elements since fall.   

I hope I wasn't to confusing.

Until Next Time.

Teaser Video Of The Adapting Of The Lionel ZW 275 Watt Transformer To DC Use

Sorry everyone I thought I was going to have more time to get my newest post on adapting my old Lionel 275 watt ZW Transformer to DC use done, but I have had some things come up and have not had time to get my new post together. 

I should have it posted by Sunday at the latest. Anyway thought I would post a teaser video of the ZW powering my Brass Pecos River 3450 Class Santa Fe 4-6-4 Hudson. 

Installing A New Can Motor Part 2

I thought I would post some more photos on my can motor install. The install is a cheap and quick  way of doing a re-motor. I have seen this technique used in HO scale and O scale with great success.

Overhead view of the install

The motor I used is a Pittman 8424,  I chose this motor because of recommendation from other forums we will see how it goes. I have to say so far I am impressed with it.

I Installed a NWSL 415-6 Flywheel, I don't really know if this size of Flywheel will make much difference in the running capability of the motor but just in case.  

I used silicone to help hold the motor in place. It makes a good dampener as well. Also here is a view of the old motor.

Here is another view of shaft connection using vacuum line.

Everyone until next time 

Installing A New Can Motor In The 2-10-4 Part 1

Hello everyone, thought I would post about the replacing of the open frame motor on my KTM 2-10-4 with a can motor.  I would call  my method on doing this a quick and dirty way to installing a can motor.  I have seen other people doing this with very good results. I am sorry I didn't take any photos during the installation of the motor. 

Anyway I could not sleep the other night so I decided to work on the 2-10-4, was so involved in the install I forgot to take pictures, but below is a short film of the install running back and forth on the track,must say it seems to run very smooth.
there is also some pictures after the fact of the install 

Here is a overall view of the install with supplies

  

Tie Strap Clip, I use 2 of them in the install to set the motor on, I file down the top to help get the proper alignment of the motor and drive shafts or if needed I can add shims to the bottom for the alignment.

This photo shows the tie strap going through the strap clip

After installing the clips and adjusting the clips for shaft alignment I silicone the motor in place on top of the clips I let the silicone dry for 24 hours, Even without the tie strips the motor is very solid.   

I will Post Part 2 Monday